JIS G0404 PDF

Find the most up-to-date version of JIS G at Engineering JIS G Steel and steel products — General technical delivery requirements (Foreign Standard). Available for Subscriptions. Content Provider. Hi! I am finding JIS G , English version, who have this standrad. Pls, upload.

Author: Gror Voodoohn
Country: Sweden
Language: English (Spanish)
Genre: Politics
Published (Last): 5 August 2009
Pages: 185
PDF File Size: 3.33 Mb
ePub File Size: 7.93 Mb
ISBN: 319-7-46105-789-9
Downloads: 71656
Price: Free* [*Free Regsitration Required]
Uploader: Meztigis

JIS has changed “for drawing” to “for processing”. The portions with continuous sidelines or dotted underlines are the matters in which the content of the corresponding International Standard has been modified.

Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. NOTE 1 The steel sheet and strip may be de scaled by pickling or shot blasting after the hot-rolling operation on request by the purchaser. Table 2 Chemical composition Unit: Hardness not in table of SAE, is calculated by interpolation.

This is the unique configura- tion of JIS and is kept as it is. In JIS there is no description of the inside diameter and the maximum outside diameter of the coil.

Over 5 min. However, the bend test may be omitted unless requested by the purchaser. Analytical test is specified.

JIS G (Outdated-currently )

Informative Hardness HRB 45 min. Since terms are defined in JIS Git is kept as it is. Inspection observed by the purchaser is deleted in JIS. Table 16 is 0g404 to those by ordinary cutting method, table 17 is applied to those re -cut or precision cut and table 18 is applied to those slit.

Related Articles  PARTITURA AL QUE ES DIGNO MARCOS WITT PDF

JIS G 热轧低碳钢板、薄板和钢带 英文版_图文_百度文库

Over 3 to and incl. Packaging and distribution of goods The flat surface plate shall be of a sufficient length to measure the flatness of steel sheets.

Since the hardness of the ji temper grade and as- annealed grade and the tensile strength of hard mate- rials can be used by commer- cial custom, they are added in JIS. Y0404 JIS, provisions for hardness test, bend test and plastic strain ratio deter- mination are added.

The steel sheets which are not bundled shall be marked for each sheet. In ISO, bendability and hard- ness were deleted at the revi- sion, and there is no provision for plastic strain ratio deter- mination. Over 4 to and incL 5 min.

JIS G3461 Seamless Boiler Tube

The products covered by this Standard are for general use and it is not required. However, tolerances of Class B may be applied as agreed between the purchaser and the supplier.

You have no items in your shopping cart. For those of diameter 3 mm or less, the reduction of area is not specified. For steel sheet excluding cut lengths thereof One test piece each for tensile and bend tests shall be taken from each test lot of the same heat where the maximum thickness of the steel sheet is within twice the minimum thickness thereof.

Related Articles  ECUACIONES DIFERENCIALES CON APLICACIONES DE MODELADO DENNIS G ZILL DOWNLOAD

I G404 of the standard temper grade and as-annealed grade Hardness of the standard temper grade and as-annealed grade shall be in accordance with either An- nex 1 table 1 or Annex 1 table 2. Over 4 to and inc!.

Provisions of hardness is nec- essary for hard materials of JIS. Two wires are shown below, carrying 3. IDT 13 Test Analytical test, tensile test, hardness test, bend test and plastic strain ratio determination are specified. However, those of wires of 32 mm or over in wire diameter shall be as agreed upon between the purchaser and the supplier.

When the flaw depth is especially requested to be eontrolled for 15 mm max. The specification in ta- ble 4 shall be applied to steel sheet and coil of as-anneal or standard temper only. Provisions on defects other than holes and lamination, however, g04004 generally be applied to one side of the surface 4 of the steel sheet and coil.

In the case where the width is less than 30 mm, however, the measurement shall be made at a mid-width position. Over 3 to and incL 6 Over 6 to and incL 10 Over 10 jos and inel. Latest News of the Blog.